|
|
|
|
TinyTrak3 to HT (Handheld) Cables
HT1C / HT1P - For Yaseu, ADI, Radio Shack Handhelds with separate Ear and Mic JackYaesu FT-411, FT-470, FT-530, and more. ADI AT-201 and more. Radio Shack HTX-202 and more. This 18-inch cable will connect a TinyTrak3 to many handheld radios with a 1/8" earphone jack, and a 3/32" microphone jack. This cable can be used with Yaesu HTs with the 4-condutor mic/ear jack if combined with the Yaesu CT-91 or CT-44 adaptors. This cable should also work on Icom handhelds. The only difference with the HT2 cable is that the HT1 has a mono plugs. R8 MUST be included on the TinyTrak PCB to use this cable. This cable is available with a cigarette lighter plug or an Anderson Powerpole. 
HT1C - $19.
With a fused cigarette lighter plug. Wiring Diagram
HT1P - $19.
With an unfused Powerpole connector. Wiring Diagram See Fuse Notes below.
HT2C / HT2P - For Icom Handhelds with separate Ear and Mic JackIcom T2H, IC-2AT, IC-V8, and more. This 18-inch cable will connect a TinyTrak3 to many handheld radios with a 1/8" earphone jack, and a 3/32" microphone jack. This cable should also work on other handhelds. The only difference with the HT1 cable is that the HT2 has a stereo plugs. This cable has been confirmed to NOT work with with Yaesu CT-91 adapter. R8 MUST be included on the TinyTrak PCB to use this cable. This cable is available with a cigarette lighter plug or an Anderson Powerpole.
HT2C - $19.
With a fused cigarette lighter plug. Wiring Diagram
HT2P - $19.
With an unfused Powerpole connector. Wiring Diagram See Fuse Notes below.
HT4C / HT4P - For Yaseu and Icom Handhelds with a Single 4-Conductor Ear and Mic JackYaesu VX-150, VX-2R, VX-5R & Icom This 18-inch cable is NOT compatible with the Yaesu VX-7R, VX-170 or other Yaesu HTs with a threaded 4 conductor ear/mic jack! This cable will connect a TinyTrak3 to the Yaesu and Icom handheld radios with a single un-threaded 1/8" 4 conductor jack. The radio plug is a right angle connector. If you use the Yaesu CT-91 or CT-44 adapter to convert the 4 conductor jack to two separate ear and mic jacks, you should use cable HT1C/HT1P above. R8 MUST be included on the TinyTrak PCB to use this cable. This cable is available with a cigarette lighter plug or an Anderson Powerpole. Note: It has been reported that this cable doesn't fit well with some Yaesu HTs. If you already have the CT-44 or CT-91, it would be better to get the HT1 cable to be sure of a good fit.
HT4C - $19.
With a fused cigarette lighter plug. Wiring Diagram
HT4P - $19.
With an unfused Powerpole connector. Wiring Diagram See Fuse Notes below.
HTKC / HTKP - For Kenwood Handhelds with separate Ear and Mic JackTH-78A, TH-D7A, and more. This 18-inch cable will connect a TinyTrak3 to most Kenwood handheld radios with a 3/32" earphone jack, and a 1/8" microphone jack. R8 should NOT be included on the TinyTrak PCB to use this cable. This cable is available with a cigarette lighter plug or an Anderson Powerpole. Sorry, HTKC & HTKP cables are out of stock. Wiring Diagram Fuse Notes
The Powerpole cables do not include fuses. These should only be plugged into a fused power supply. In-line fuses can be purchased from
PowerWerx.
While these cables have been confirmed to work on the radios listed, you must use them at your own risk. Byonics is not responsible for damage resulting from these cables. See More Byonics Cables |